Netcomm NP725 Bedienungsanleitung

User GuideNP725 User Guidewww.netcomm.com.auNP725 - Wireless Access Point

Chapter 3. Installation 7 3.2 Basic Configuration NP725 provides the web management interface for configuration. After completing hardware installat

Chapter 3. Installation 8 After successfully logging into NP725, the System Overview page of the web management interface will appear. To logout, si

Chapter 3. Installation 9 Configure AP Settings 1) Click on the AP menu item. Select General submenu. 2) Determine the Band and Channel Selec

Chapter 3. Installation 10 Check AP Status After finishing the settings, the enabled virtual AP should appear in the virtual AP list showing enabled

Chapter 3. Installation 11  Change Security Type to WEP If WEP is preferred, supply the desired Authentication, key length, format, index and val

Chapter 3. Installation 12  Change Security Type to 802.1X If 802.1X authentication is preferred, supply the desired WEP key length and the corres

Chapter 3. Installation 13  Change Security Type to WPA-PSK If WPA-PSK is preferred, supply the desired pre-shared key and cipher type.

Chapter 3. Installation 14  Change Security Type to WPA-Radius If WPA-Radius is preferred, supply the cipher type and the corresponding settings

Chapter 3. Installation 15 Configure WDS Settings 1) Click on the WDS menu item. 2) Select WDS Configuration submenu item. 3) Setting WDS link

Chapter 3. Installation 16 Congratulations Now, the system has been installed and configured successfully. Note: It is strongly recommended to

Table of Contents Chapter 1. Introduction ...

Chapter 4. Web Management Interface 17 Chapter 4. Web Management Interface This chapter provides further information on the NP725 configuration. The

Chapter 4. Web Management Interface 18 Introduction: NP725 has equipped a friendly Web graphical user interface for users and system administrators

Chapter 4. Web Management Interface 19 In each configuration page, the active menu and submenu item will be shown in different color to indicate whic

Chapter 4. Web Management Interface 20 4.1 System This section provides information on the following functions: System Information, Network Settings,

Chapter 4. Web Management Interface 21 ¾ Device Time: Current system time ¾ Time Zone: Take UTC offset to set this field ¾ Synchronization: There a

Chapter 4. Web Management Interface 22 1) NTP Enabled: By enabling NTP server, NP725 can synchronize its system time with the NTP server automatica

Chapter 4. Web Management Interface 23 4.1.2 Network Settings There are two methods of IP configuration available in NP725. LAN interface configurat

Chapter 4. Web Management Interface 24 4.1.3 Management Services For easier maintenance, SNMP (Simple Network Management Protocol) and remote syslog

Chapter 4. Web Management Interface 25 4.2 AP This section provides information on the following functions: Overview, General, VAP Configuration, Secu

Chapter 4. Web Management Interface 26  Security Type: The hyperlink showing security type connects to the screen of Security Settings.  MAC ACL:

4.5.3 WDS List Status ...

Chapter 4. Web Management Interface 27

Chapter 4. Web Management Interface 28 4.2.2 General Settings  Band: The operating wireless frequency band of the device. Choose among frequency ban

Chapter 4. Web Management Interface 29 4.2.3 VAP Configuration To enable each VAP in the NP725, the administrator has to configure each VAP manually.

Chapter 4. Web Management Interface 30 4.2.4 Security Settings The NP725 supports various user authentication and data encryption in each VAP's p

Chapter 4. Web Management Interface 31  802.1X: Provides RADIUS authentication and dynamic WEP.  WPA-PSK: Provides shared key authentication and

Chapter 4. Web Management Interface 32  WPA-RADIUS: Authenticate user by RADIUS and provide WPA data encryption.

Chapter 4. Web Management Interface 33 4.2.5 Advanced Wireless Settings Virtual AP advanced settings should mostly meet general requirements. Take t

Chapter 4. Web Management Interface 34 4.2.6 Access Control Settings The NP725 supports various methods to authenticate clients from using wireless L

Chapter 4. Web Management Interface 35  Deny List When the policy is set to Deny List, all wireless connections to the VAP will be allowed except

Chapter 4. Web Management Interface 36

Chapter 1. Introduction 1 Chapter 1. Introduction 1.1 Overview This manual is written to assist system integrators, field engineers and network admi

Chapter 4. Web Management Interface 37 4.3 WDS This section provides information in the following functions: Overview and WDS Configuration. The confi

Chapter 4. Web Management Interface 38 4.3.2 WDS Link Settings For each WDS link profile, the administrators need the remote peer's MAC address

Chapter 4. Web Management Interface 39 4.4 Utilities This section provides information on four utilities used for customizing and maintaining the syst

Chapter 4 Web Management Interface 40 4.4.2 Configuration Save / Restore This function is used to backup and to restore the NP725 settings. The NP725

Chapter 4. Web Management Interface 41 4.4.3 System Upgrade NP725 provides Web firmware upload/upgrade feature. While the new firmware is obtained, it

Chapter 4. Web Management Interface 42 4.4.4 Reboot This function allows the administrator to restart the NP725 safely. The process should take about

Chapter 4. Web Management Interface 43 4.5 Status This section provides information on the following functions: Overview, Clients, WDS List and Event

Chapter 4. Web Management Interface 44 The description of the table is as the following: Item Description System Name The system name Firmware Versio

Chapter 4. Web Management Interface 45 4.5.2 Associated Client Status List all associated clients from all the VAPs. Please take this table to manage

Chapter 4. Web Management Interface 46 4.5.3 WDS List Status The list shows the WDS link status with information such as Link Status, MAC Address, S

Chapter 1. Introduction 2 1.3 Deployment Topology Examples The above deployment scenario illustrates a deployment example using three access points,

Chapter 4. Web Management Interface 47 4.5.4 Event Log Event log provides the system activities records and monitor the system status by checking thi

Chapter 4. Web Management Interface 48 4.6 Online Help The Help button is at the upper right corner of the display screen. Click Help for the Online

Chapter 4. Web Management Interface 49 4.7 Legal & Regulatory Information This manual is copyright. Apart from any fair dealing for the purposes

Chapter 4. Web Management Interface 50 (3) The power supply that is provided with this unit is only intended for use with this product. Do not use t

Chapter 4. Web Management Interface 51 Limitations of Warranty The Trade Practices Act 1974 and corresponding State and Territory Fair Trading Acts or

Product WarrantyNetComm products have a standard 12 months warranty from date of purchase. However some products have an extended warranty option, via

Chapter 2. System Overview 3 Chapter 2. System Overview 2.1 Package Contents The standard package of NP725 includes: y NP725 x 1 y CD-ROM with pr

Chapter 2. System Overview 4 Rear Panel  Power Socket: Connects to the power adapter provided.  RESET Button o Press the button to restart t

Chapter 2. System Overview 5 Top Panel LED:  Power: ON indicates that power is on and OFF indicates that power is off.  LAN1/LAN2: OFF indica

Chapter 3. Installation 6 Chapter 3. Installation 3.1 Wireless LAN Access Point Connection Please follow the steps below to install the hardware of